New Electric Guitar Models

Gilmour inspired Custom JM
Gilmour inspired Custom JM
IMG_2529
The Rev
IMG_2528
The Rev
Gilmour inspired Custom JM
Gilmour inspired Custom JM
IMG_2272
Tele Mod
DSC02925
Custom Selcouth v2
DSC02940
Custom Selcouth v2
IMG_2413
Custom Selcouth
IMG_2500
Strut
IMG_2515
Strut
IMG_1270 (1)
Seti v2
IMG_1274
Seti v2
Custom VI
Custom VI
Seti Model
Seti Model
Selcouth model
Selcouth Model
"Oilcaster" tele
“Oilcaster” tele
"The Smith" custom built for Debbie Smith (Blindness, Curve, Echobelly, London Dirthole Company)
“The Smith” custom built for Debbie Smith (Blindness, Curve, Echobelly, London Dirthole Company)
The Rocktopus custom built for Gary Arce (Yawning Man, ZUN, Ten East, Waterways, Sort of Quartet)
The Rocktopus custom built for Gary Arce (Yawning Man, ZUN, Ten East, Waterways, Sort of Quartet)
The Rocktopus custom built for Gary Arce (Yawning Man, ZUN, Ten East, Waterways, Sort of Quartet)
The Rocktopus custom built for Gary Arce (Yawning Man, ZUN, Ten East, Waterways, Sort of Quartet)
Selcouth v2 Model
Selcouth v2 Model

Saving “Miss Kay”

One of my favorite things to do in this business is save great old guitars. Especially the cheap ones because you can get creative with very little stress. Awhile back one of my customers, a local player named Gus Campbell (www.guscampbellmusic.com), brought me his old 1950’s Kay guitar.

Miss Kay
Miss Kay

He was rather distraught having found that after restringing it the bridge, which was a string through wrap around design, had broken.

Broken bridge
Broken bridge

The usual remedy would be to remove the old bridge, make a new one and string it back up except this guitar was old and to ever play right it would need a neck reset as well and it just wasn’t worth it monetarily nor would it be an easy job! So I started asking questions about the guitar…when did you get it, what songs are you using it on, anything to get a feel for how it was used. Then he mentioned what I wanted to hear. “I mainly use it for slide” he said. Then the lightbulb went off…why not make Miss Kay a slide machine? With the high action that suits a slide guitar, the neck reset would be unnecessary and I could use the existing bridge as a base for a tune-o-matic bridge. With the addition of a trapeze tailpiece I could make this thing work! So I started off. First I routed off the broken part of the bridge.

Broken bridge routed off
Broken bridge routed off

It would need to be gone to instal the tune-o-matic, but doing so would weaken the area significantly and I’d need something to sink the bridge posts into, so I decided to create a simple brace that would mount to the inside of the bridge plate.

Inside brace
Inside brace

I figured I could kill two birds with one stone and pre drill the pilot holes for the posts in both the bridge and the brace. I figured out the measurements to get good intonation with the new bridge and marked and drilled the holes. But then, how to align them while glueing? Easy, I grabbed two toothpicks and inserted them in the brace. Then it was quite simple to spread on some wood glue, reach into the guitar, and push the toothpicks up through the holes.

IMG_3374
Clamping the brace

The glue held the brace in place while I applied clamps and once secured, I just pulled out the toothpicks…easy.

Once the glue had set it was just a matter of installing the posts and setting on the bridge. I found an old Kay trapeze tailpiece and installed that as well.

Vintage Kay trapeze tailpiece
Vintage Kay trapeze tailpiece

A set of strings later she was up and running!

IMG_3379

Gus was happy and played some gigs using Miss Kay for his slide songs and a few weeks later called and said he loved it so much he wanted to make it electric, I was definitely on board for this! So we chose a pickup, in this case a McNelly Stagger Swagger (www.mcnellyguitars.com). I didn’t want to have to modify the guitar too much so I made a mounting plate for the pickup that would clamp itself in using some ebony blocks (much like a Sunrise acoustic soundhole pickup or any number of others).

IMG_3616

I airbrushed a little colored shellac to match the guitar, but I wanted it to look a little old and amateurish, this was a 60 year old Kay after all, no need to get fancy…just make it work. We decided to add a volume and tone control to the upper bout.

IMG_3617

This was easy enough, I mounted the harness to a thin maple plate, drilled the holes in the body, and once it was wired up, they were mounted to the side. I popped on a couple of old speed knobs and she was ready to rock!

IMG_3620IMG_3623

Sharp Fret Ends

I live in Phoenix, AZ. It’s extremely dry here and if you live in a dry climate you have most certainly picked up a guitar with an unbound fretboard and found the frets sharp and uncomfortable due to the neck shrinking. This is such a common problem, especially on Fender guitars, ¬†that I’ve done nearly 20 of these jobs in the last 2 months. I figured I’d share my method because it’s extremely easy. I would not use this exact method on a very valuable guitar, for those I will tape off the fretboard and generally be far more careful with finish and even the final shape of the fret ends, but since most guitars are “players”, this is the most common method I use…This example is a MIM Strat with really sharp frets…

IMG_2694

The frets are protruding and the bottom corners are very sharp…The first step is to tape off the side of the neck with blue masking tape right below the bottom of the fret tang…

IMG_2695

This not only protects the finish, but it will provide a “stop” when you begin sanding. The tape will keep you from taking off more than just the protruding frets. You’ll hit the finish just a tad, but we’ll remedy that later…Once the neck is taped off, get a hard, flat sanding block. I use a small piece of maple, sanded flat. ¬†Attach 400grit paper to the flat side and sand the edge of the neck (the fret ends) with the block, perpendicular to the board…

IMG_2697

Do this until you can no longer feel the frets underneath the block…in other words, once the block glides smoothly along the edge of the neck STOP and move on to the other side. It will usually take 2 pieces of sandpaper. Once the tangs are sanded smooth, tilt the block in to match the bevel of the fret ends and sand lightly…

IMG_2698

Now the frets should be more comfortable BUT you’re gonna need to take care of the bottom of the fret ends. Use a 3-corner file to lightly file the bottom corners. 2 quick, light swipes on both sides will be sufficient…

IMG_2699

IMG_2701

Now you’ll want to clean up the file marks and the sanding you’ve done. The best option is Micro Mesh.

IMG_2704

Go thru each grit, concentrating on the fret ends but also hitting the edge of the neck above the tape…this will polish up any sanding marks on the finish. One cool side effect of this method is that the fretboard edges will get just slightly rolled like an old vintage guitar. Before moving on to the next grits it’s a good idea to gently hit the top of the frets, and even the board, just a tad to clean them up. This is a few quick swipes up and down the board with each grit…

IMG_2705

Once you’re thru all the grits the fret ends should be nice and polished. Clean and oil the board, and it’s all done…

IMG_2707

IMG_2712

Cheers!

 

Fender Roadworn Tele

A friend recently brought me two of his Teles, one was a stock Fender Roadworn and the other was a parts tele…Warmoth neck on an American Tele body. Neither of them was “useful” to him anymore so we discussed what to do. We decided to mod the Roadworn body, adding an offset vibrato, a B-5 conversion plate with a Mastery Bridge (by far the best offset bridge available…if you have a Jazzmaster or Jaguar, etc, and you don’t have a Mastery on it, GET ONE!), and use the Warmoth neck which was a beautiful flame maple neck w/ rosewood board. The neck however had been finished years before by another builder and was not up to par…thick finish with a badly applied decal…so we decided we’d refin the front of the headstock, black it out, and add my company logo in metallic green. I also modded the electronics just a bit, replacing the stock capacitor with an Emerson PIO cap (available from Stew Mac and a very good cap. I prefer NOS Cornell-Dubilier, Sprague Vitatmin-Q’s, or Russian military caps on my custom builds, but the Emerson works fantastic as an upgrade to stock electronics). In the end we arrived at a whole new guitar, here’s the end result…

IMG_2753

IMG_2755

IMG_2756

Model PT

PT

Curly maple back and sides, Sitka spruce top, ebony binding w/flamed sycamore lines, and maple burl end graft.

PT1

Scoop cutaway.

PT3a

 

This model is my answer to the current resurgence of the Parlor guitar. It has a small, asymmetrical body (though it doesn’t look like it at first glance), a 24.9″ scale and a 13th fret joint so that there are a full 12 frets above the body joint. It is a small guitar, but it has huge sound. The next one will be under construction shortly.

Cheers

Making a Carved Top Electric Guitar…Without Any Carving (Part 3)

In Part 2 the carve began to take it’s final form. The recurve was added with the aid of a curved scraper, so we are ready to go back to the random orbit sander. I will burn thru a few more discs of 80 grit, often times using the front edge of the sander to hog off a lot of material where needed. I try to blend from a generally flat surface under the bridge/tailpiece to a smooth sweeping curve down to the recurve and back up to the edge (binding). Here’s what it looks like after nearly all the “carving” is done…

P1010004

The next step is to finish off the neck end. I will fit the neck blank in, without the fingerboard, and check the centerline and the pitch. When this is all correct I simply trace along the fingerboard surface inside the neck pocket and sand down to that line…

P1010018

Now when the neck is attached the fingerboard will follow the carve right up to the correct pitch. The last step for me, besides the eventual rear control cavity routs, drilling, and finish sanding is to make sure the recurve and transition areas are all smooth. I do this with a round rubber sanding block and 80 grit, knocking off any peaks and valleys, especially in the recurve area. You can see here how I try to shape things, like the recurve, based on the tools I have available or the tools I prefer to use. It is no accident that my favorite sanding block and the recurve on the guitar are nearly identical.

P1010031

This entire body was taken from a shaped blank to it’s final form in one morning before lunch. Of course there is a lot of other work to do, but this method allows you to quickly produce a pretty killer carved top body. Here is the finished product…

djb4

djb1

djb3

I hope this has been informative. Cheers!